Advanced Search Results
Refine your search by using the category filter.
Spherical Copper Powder - 100 Mesh - 99.5% Cu
High-purity spherical copper powder consisting predominantly of spherical copper particles with a bright reddish-copper appearance. The 100 mesh grade is coarse relative to fine and ultra-fine copper powders. Because the particles are rounded and smooth, the powder flows freely, packs to a high tap density, and behaves consistently during die filling and dosing.
Calibrated microscopy of the current material shows that the mass is carried primarily by coarse spheres near the top of the 100 mesh cut, together with a population of smaller particles that contributes relatively little to the overall mass. This produces the characteristic appearance of larger spheres surrounded by finer particles. Practically all of the material passes through mesh 100 sieve, corresponding to an opening of approximately 150 microns, and the typical mass-median particle size is approximately 120 microns.
The coarse spherical morphology provides a lower specific surface area than fine or ultra-fine copper powder, contributing to improved storage stability and slower development of surface oxidation. Copper powder may exhibit limited electrical continuity when tested as loose powder because individual particles are not necessarily in continuous contact. Conductivity can increase substantially after compaction or when the powder is incorporated into a suitable resin, oil, polymer, or other matrix.
Product Specifications
| Product | Spherical Copper Powder |
| Assay | 99.5% Copper minimum |
| Current Lot Analysis | 99.95% Copper |
| Mesh Grade | 100 Mesh |
| 100 Mesh Sieve Opening | Approximately 150 microns |
| Typical Mass Median (Dv50) | Approximately 120 microns, based on image analysis |
| Particle Morphology | Predominantly spherical to near-spherical |
| Appearance | Reddish-copper metallic powder |
| Chemical Symbol | Cu |
| CAS Number | 7440-50-8 |
| HTS Code | 7406.10.0000 |
| NMFC | 30743 |
Typical Particle Size Distribution
The values below are typical mass-based results obtained from calibrated optical image analysis of the current material. Percentages are cumulative and represent the share of total mass finer than each listed sieve opening. These values are provided as general guidance for particle-size selection and may vary from lot to lot.
| Sieve | Opening | Typical Cumulative % Passing by Mass |
| 100 Mesh | 150 microns | About 99% |
| 120 Mesh | 125 microns | About 64% |
| 140 Mesh | 106 microns | About 23% |
| 170 Mesh | 90 microns | About 12% |
| 200 Mesh | 75 microns | About 5% |
| 325 Mesh | 45 microns | About 1% |
Typical percentile sizes by mass are approximately Dv10 near 85 microns, Dv50 near 120 microns, and Dv90 near 135 microns. Most of the mass falls between approximately 105 and 150 microns, resulting in a coarse, relatively narrow particle-size distribution immediately below the 100 mesh opening. A finer particle population is present by particle count but contributes relatively little to total mass. These figures are derived from image analysis and are not a certified sieve analysis.
Particle Characteristics
- Predominantly spherical and near-spherical copper particles with smooth metallic surfaces.
- Free-flowing morphology supports even die filling and consistent dosing.
- Good packing characteristics and high tap density associated with spherical morphology.
- High metallic copper content of 99.5% minimum supports electrical and thermal conductivity after compaction or incorporation into a suitable matrix.
- Lower specific surface area than fine or ultrafine copper provides improved storage stability and slower surface oxidation.
- Coarse spherical particles carry most of the material mass, with a finer population present primarily by particle count.
- Material mass is concentrated near the upper end of the 100 mesh cut, with essentially all material passing 100 mesh.
- Bright reddish-copper metallic appearance.
- Suitable for formulations requiring metallic copper with a relatively coarse, controlled particle size.
Applications and Benefits:
- Powder metallurgy and press-and-sinter components.
- Sintered porous parts, including filters and self-lubricating bearings, where spherical morphology can provide controlled, interconnected porosity.
- Metal-filled polymers, resins, and epoxies.
- Thermally conductive compounds and gap fillers.
- Bulk metallic filler in compounded conductive pastes, adhesives, and sealants. This is a coarse-particle filler rather than a fine-line printing ink powder.
- Cold casting and metal-filled resin castings that can be sanded and polished to produce a metallic copper surface.
- Decorative metallic epoxy, resin, and coating finishes requiring a visible copper effect.
- Metal-bonded matrix and friction formulations using copper as a matrix metal.
- Copper-based brazing and joining formulations.
- Copper metal reagent for laboratory and research chemistry.
- Educational demonstrations involving metallic powders.
- High-density and specialty industrial filler applications.
Caution:
Fine metal powders should be handled carefully to minimize airborne dust. Avoid inhalation, unnecessary dust generation, and contact with incompatible materials or ignition sources. Refer to the current SDS for complete handling, storage, personal protection, and disposal information.
Copper Powder 99+%, Mesh 200
High-purity copper powder made via water atomization and hydrogen reduction. Features very fine, irregular particles and clusters with relatively lower density. Recommended for applications requiring high purity and conductivity, including diamond wheels, sintering, and chemical reactions. Note: Pure copper powders may not exhibit conductivity under low-voltage tests but will conduct when compacted or mixed with oils or resins.
Product Specifications
| Purity | 99.3% |
| Hydrogen Loss | 0.39% |
| Apparent Density | 2.6 - 2.8 g/cc |
| Mesh Size | 200 mesh |
| Sieve Analysis |
+100 Mesh: Trace +140 Mesh: 1% Max +200 Mesh: 3% Max +325 Mesh: Balance -325 Mesh: 90% Min |
| HTS Code | 7406.10.0000 |
| NMFC | 30743 |
| CAS No. | 7440-50-8 |
Applications and Benefits:
- Thick and thin film pastes
- Conductive inks, paints, and pastes
- Injection molding
- Thermal management
- EDM electrodes
- Antifouling paints
- Thermal sprays
- Sintered alloys/products
- Brazing/soldering paste
- Diamond wheels
- Chemical reactions
Caution:
Handle with care. Refer to the SDS for detailed safety guidelines.
Copper Powder 99.3%, General Purpose, 150 Mesh
The most popular and widely used copper powder, produced by the water atomization method followed by hydrogen reduction. This general-purpose copper powder has diverse applications, including the production of copper compounds, use as a catalyst in chemical formulations, abrasive wheels, carbon brushes, and more. It is important to note that pure copper powders may not exhibit continuity or conductivity under low-voltage multimeter tests due to air gaps and weak particle contacts but will show conductivity under higher voltage, when compacted, or mixed with oils/resins to form a paste.
Product Specifications
| Purity | 99.3% |
| Apparent Density | 2.7 g/cc |
| Nominal Mesh | -140 |
| -325 Mesh Ratio | > 50% |
| HTS Code | 7406.10.0000 |
| NMFC | 30743 |
| CAS No. | 7440-50-8 |
Applications and Benefits:
- Production of copper compounds
- Catalyst in chemical formulations
- Abrasive wheels
- Carbon brushes
- Electronics and electrical applications
- Decorative and protective coatings
- Brazing and general-purpose industrial use
Caution:
Handle with care. Refer to the SDS for detailed safety guidelines.
Copper Powder 99.3%, Mesh 325
Ultra-fine, high-purity copper powder made via water atomization and hydrogen reduction. Features spheroidal particles and clusters, offering higher conductivity and lower density. Suitable for metal injection molding and applications requiring high conductivity and purity. Typical applications include conductive inks, paints, pastes, thermal sprays, and sintered products. Note: Pure copper powders may not exhibit conductivity under low-voltage tests but will show conductivity when compacted or mixed with oils or resins.
Product Specifications
| Purity | 99.31% |
| Hydrogen Loss | 0.39% |
| Apparent Density | 2.97 g/cc |
| Mesh Size | 325 mesh |
| Sieve Analysis |
+60 Mesh: 0% -60/+80 Mesh: 0% -80/+100 Mesh: 0% -100/+140 Mesh: Trace -140/+200 Mesh: Trace -200/+325 Mesh: 0.6% -325 Mesh: 99.4% |
| HTS Code | 7406.10.0000 |
| NMFC | 30743 |
| CAS No. | 7440-50-8 |
Applications and Benefits:
- Thick and thin film pastes
- Conductive inks, paints, and pastes
- Injection molding
- Thermal management
- EDM electrodes
- Antifouling paints
- Thermal sprays
- Sintered alloys/products
- Brazing/soldering paste
Caution:
Handle with care. Refer to the SDS for detailed safety guidelines.
Copper Powder 99.8%, Electronic Grade, Mesh 325
Electronic grade, high-purity copper powder made via water atomization and hydrogen reduction. Features ultra-fine, spheroidal particles with high conductivity and low density. Recommended for a variety of applications where conductivity is crucial, including thick and thin film pastes, capacitor chips, and thermal sprays. Note: Pure copper powders may not exhibit conductivity under low-voltage tests but will conduct when compacted or mixed with oils or resins.
Product Specifications
| Purity | 99.85% |
| Hydrogen Loss | 0.19% |
| Apparent Density | 2.97 g/cc |
| Mesh Size | 325 mesh |
| Sieve Analysis | +60 Mesh: 0% -60/+80 Mesh: 0% -80/+100 Mesh: 0% -100/+140 Mesh: Trace -140/+200 Mesh: Trace -200/+325 Mesh: 0.6% -325 Mesh: 99.4% |
| HTS Code | 7406.10.0000 |
| NMFC | 30743 |
| CAS No. | 7440-50-8 |
Applications and Benefits:
- Thick and thin film pastes
- Capacitor chips
- End cap terminators
- Conductive inks, paints, and pastes
- Injection molding
- Electronics
- Thermal management
- EDM electrodes
- Thermal sprays
- Sintered alloys/products
- Brazing/soldering paste
Caution:
Handle with care. Refer to the SDS for detailed safety guidelines.
Copper Powder > 99% (150 - 325 Mesh)
General-purpose, highly pure (>99%) copper powder made from electrolytic copper. Granular copper with a mesh size of 150 - 325. Known for its excellent electrical and thermal conductivities, this product finds use in the electrical and electronic industries. Additional applications include self-lubricating bearings, brazing, cold soldering, and mechanical plating. It is also used for antifouling paints, decorative and protective coatings, printing inks, medals, medallions, metal-plastic decorative products, and various chemical and medical purposes.
Product Specifications
| Purity | >99% |
| Mesh Size | 150 - 325 |
| Screen Analysis |
+60: 0.0% -60/+100: 0.7% -100/+200: 89.7% -200/+325: 9.1% -325: 0.5% |
Applications and Benefits:
- Electrical and electronic applications
- Self-lubricating bearings
- Brazing and cold soldering
- Mechanical plating
- Antifouling paints and decorative coatings
- Printing inks
- Medals, medallions, and metal-plastic decorative products
- Chemical and medical purposes
Caution:
Handle with care. Refer to the SDS for detailed safety guidelines.
CU264: Copper Powder, 99.5%, Mesh 100
High purity copper powder, nominal mesh 100, Apparent density: 2.6 g/cc, Copper > 99.5%, with irregular shape particles. Used in powder metallurgy. May be admixed with other metal powders and graphite for specific properties such as strength, hardness and wear resistance for structural parts.
HTS Code: 7406.10.0000
NMFC: 30743
CAS: 7440-50-8
Note: Pure copper powders do not show continuity or conductivity when tested with a multimeter. This might be due to two reasons. One reason is the low voltage used for the test. The other reason is the presence of air and weak contacts between the particles. They will exhibit conductivity with higher voltage, when compacted, and when mixed with some oil or resin to form a paste.
Safety Data Sheet for Copper Powder
Key Features
- High Purity Copper (>99.5%)
- Nominal Mesh 100 for fine granularity
- Irregular particle shape for diverse uses
- Compatible with other metals and graphite
- Conductivity with higher voltage or when compacted
Product Specifications
| Apparent Density | 2.6 g/cc |
| Purity | > 99.5% Copper |
| Particle Shape | Irregular |
| Conductivity | At higher voltages/when compacted |
| Applications | Powder Metallurgy, Alloys |
Similar Products
- High purity bronze powder, metallurgy
- Fine granular aluminum powder, industrial
- Nickel powder, high density, 99% purity
- Spherical zinc powder, corrosion-resistant
- Iron powder, magnetic, for alloys
Note: These are similar products, and each product is different, so research is required to find the best fit for your needs.
Perfect for Metallurgists, Industrial Manufacturers, Material Scientists, Engineering Students, Research and Development Labs
CU7005F Copper Powder
Copper Powder offers exceptional metallic shine, ideal for metallic inks and paints. Compatible with most resins and conductive for ink creation.
For more details, visit the CU7005F product data sheet.
Key Features
- Exceptional metallic shine
- Art-grade pigment quality
- Compatible with various resins
- Usable with drying oils like linseed
- Enables creation of conductive inks
Product Specifications
| Type | Copper Powder |
| Use | Metallic Inks, Paints |
| Compatibility | Polyurethane, Polyacrylic, Polyester |
| Conductivity | Suitable for Conductive Inks |
| Pigment Quality | Art Grade |
Similar Products
- Metallic-shine gold powder for inks
- Silver pigment powder, art-grade
- Bronze powder, resin-compatible
- Reflective aluminum powder, versatile
- Artistic brass powder for painting
Note: These are similar products, and each product is different, so research is required to find the best fit for your needs.
Perfect for Artists, Paint Manufacturers, and DIY Craft Enthusiasts
Cork Borer Set With Metal Handles Set Of 6
Introducing our Cork Borer Set With Metal Handles Set Of 6, perfect for laboratory and scientific use. Made of plated sharpened brass tubing with attached metal handles, this set includes a steel punch and six borers with diameters of 5-mm, 6-mm, 8-mm, 9-mm, 10-mm and 11-mm. This set can be used to punch a hole in cork and natural rubber stoppers and can be sharpened using a cork borer sharpener tool. Get accurate and precise results with our Cork Borer Set With Metal Handles Set Of 6.
Key Features:
- Set of 6 cork borers with metal handles
- Made of plated sharpened brass tubing
- Diameters of holes made: 5mm, 6mm, 8mm, 9mm, 10mm, and 11mm
- Can be used to punch holes in cork and natural rubber stoppers
- Includes a steel punch
- Borers can be sharpened using a cork borer sharpener tool
Unique Selling Points:
- High quality plated brass tubing for durability
- Wide range of hole sizes for versatility in use
- Metal handles provide a secure grip for precise hole punching
- Includes a steel punch for added convenience
- Borers can be sharpened for extended use
Product Specifications:
| Product Name | Cork Borer Set With Metal Handles Set Of 6 |
| Material | Borer: Plated Sharpened Brass Tubing; Handles: Metal |
| Included Items | Set of 6 Cork Borers with Attached Metal Handles and a Steel Punch |
| Borer Diameter | 5mm, 6mm, 8mm, 9mm, 10mm, 11mm |
| Function | Used to punch a hole in cork and natural rubber stoppers |
| Sharpening | May be sharpened using a Cork Borer Sharpener Tool |
Similar Products
- Cork Borer Set with Plastic Handles Set of 6
- Cork Borer Set with Wooden Handles Set of 6
- Brass Tube Punch Set with Metal Handles Set of 6
- Plated Steel Hole Punch Set with Plastic Handles Set of 6
- Adjustable Hole Punch Set with Metal Handles Set of 6
Note: These are similar products, and each product is different, so research is required to find the best fit for your needs.
Caution: Sharp tools. Handle with care to avoid injury.
Perfect for:
- Science teachers and students
- Laboratory technicians and researchers
- Chemistry and biology enthusiasts
- DIY makers and crafters
- Professionals in the pharmaceutical and food industries
- Anyone who needs to punch holes in cork or rubber stoppers
Safety Data Sheet for Copper Powder
CU41, Copper Powder, Mesh 40 (Coarse)
High purity atomized copper powder -40/ 100 US Mesh has the largest grains compared with our other copper powder products. It is also usually darker in color. Minimum purity: 99.0%. Typical Apparent Density: 2.4. Nominal Mesh: -40/ 100. HTS Code: 7406.10.0000. NMFC: 30743. CAS: 7440-50-8. Typical Analysis: Copper: 99.87%, Hydrogen Loss: 0.21%, Apparent Density: 2.57 g/cc. Sieve Analysis: 40 mesh 0%, -40/ 100 mesh 90.4%, -100/ 140 mesh 9%, -140 mesh 0.6%.
Key Features
- High purity, minimum 99.0%
- Coarse grain size, -40/ 100 US Mesh
- Dark color, distinct appearance
- Apparent Density: 2.57 g/cc
- Comprehensive sieve analysis included
Product Specifications
| Purity | 99.87% |
| Hydrogen Loss | 0.21% |
| Apparent Density | 2.57 g/cc |
| Mesh Size | >40 mesh 0% -40/ 100 mesh 90.4% -100/ 140 mesh 9% -140 mesh 0.6% |
| HTS Code | 7406.10.0000 |
| NMFC | 30743 |
| CAS Number | 7440-50-8 |
Similar Products
- Fine grain, 99% pure copper powder
- Medium grain, dark copper powder
- High-density, fine copper powder
- Coarse, 98% pure copper flakes
- Atomized, spherical copper granules
Note: These are similar products, and each product is different, so research is required to find the best fit for your needs.
Perfect for Industrial Manufacturers, Metal Fabrication Professionals, Chemical Industry Experts, Research and Development Teams, Specialty Alloy Producers
Aluminum Metal Cubes
These lightweight aluminum cubes are perfect for density comparison and experimentation. Made with precision machining, they are available in 10mm or 20mm sizes, and are an excellent addition to any laboratory or classroom.
Key Features
- Precision machining
- Lightweight aluminum material
- Available in 10mm or 20mm sizes
Product Specifications
| Material | Aluminum |
| Density | 2.7 g/cm3 |
| Size Options | 10mm or 20mm |
| Weight | Varies by size |
Perfect for:
- Science teachers and students
- Laboratory technicians
- Chemistry enthusiasts
- Physics enthusiasts
- Engineering students
- Metalworking hobbyists
Similar Products
- Copper Metal Cubes
- Brass Metal Cubes
- Titanium Metal Cubes
- Steel Metal Cubes
- Nickel Metal Cubes
Note: These are similar products, and each product is different, so research is required to find the best fit for your needs.
Caution: Handle with care. These cubes are made of aluminum, which can be a hazard if not handled properly. Keep out of reach of children and use appropriate safety equipment when conducting experiments.
Brass Metal Cubes
Looking for high-quality brass cubes for density comparison and experimentation? Look no further than our Brass Metal Cubes! Available in both 10mm and 20mm sizes, these precision machined cubes are made from top-quality brass material.
Key Features:
- Precision machining
- High-quality brass material
- Available in 10mm or 20mm sizes
Product Specifications:
| Material | Brass |
| Density | 8.4 g/cm3 |
| Size Options | 10mm or 20mm |
| Weight | Varies by size |
Similar Products:
- Copper Metal Cubes
- Aluminum Metal Cubes
- Titanium Metal Cubes
- Steel Metal Cubes
- Nickel Metal Cubes
CAUTION: Handle with care. These brass metal cubes are for experimentation and density comparison purposes only. Keep out of reach of children and avoid ingestion or inhalation. Similar products may have different properties and require research before use.
Perfect for:
- Science teachers and students
- Laboratory technicians
- Chemistry enthusiasts
- Researchers and scientists
- Engineering students
- College and university professors
Density Cubes, Metals Copper
These high-density copper cubes are for comparison and experimentation, available in 10mm or 20mm sizes, machined and made from copper material.
Product Specifications
| Material | Copper |
| Density | 8.96 g/cm3 |
| Size Options | 10mm or 20mm |
| Weight | Varies by size |
| Package Dimensions | 20 x 20 mm |
| Package Weight | 0.155 lb |
| Units per Package | 1 |
Applications and Benefits:
- Science enthusiasts
- Students studying density and material properties
- Teachers looking for hands-on classroom activities
- Researchers in materials science and engineering
Key Features and Benefits
- High-density copper material
- machined for accurate measurements
- Reusable transparent plastic case for storage
Caution:
High-density copper cubes may be hazardous if mishandled. Please use caution when handling and keep out of reach of children.
Density Cubes, Metals Iron
These iron cubes are designed for density experiments in the classroom or laboratory, available in 10mm or 20mm sizes, with precise measurements for accurate and consistent results, made from durable iron material. The cubes are packaged individually, with a weight of 0.135 lb, and are for science teachers, students, and researchers. The iron material provides a high density, making it for demonstrating density concepts.
Product Specifications
| Material: | Iron |
| Sizes: | 10mm or 20mm |
| Package Dimensions: | 20 x 20 mm |
| Weight: | 0.135 lb |
| Density: | 7.9 g/cm³ |
Applications and Benefits:
- For density experiments in the classroom or laboratory
- For science teachers, students, and researchers to demonstrate density concepts
- for hands-on learning and experimentation
Key Features and Benefits
- Iron material for high density and precise measurements
- Precise measurements for accurate and consistent results
- Reusable packaging for convenient storage
- Durable iron material for long-lasting use
Caution:
Handle with care, as iron can be sharp and heavy. Avoid touching sharp edges and keep out of reach of children.
Lead Metal Cubes
Lead Metal Cubes are high-density cubes designed for density comparison and experimentation. These cubes are made of high-density lead material and are precisely machined for accuracy. They are available in two sizes, 10mm or 20mm, to suit different needs.
Note: These are similar products, and each product is different, so research is required to find the best fit for your needs.
Product Specifications:
| Material | Lead |
| Density | 11.3 g/cm3 |
| Size Options | 10mm or 20mm |
| Weight | Varies by size |
Perfect for:
- Science teachers and students
- Chemistry enthusiasts
- Researchers
- Lab technicians
- Metallurgists
- Industrial engineers
Caution: Lead is a toxic material. Handle with care and avoid ingestion or inhalation.
Density Cubes, Metals Tin
The Density Cubes, Metals Tin are -engineered cubes crafted from high-density tin, for educational and industrial applications, including density comparison experiments and material studies. Available in two sizes, 10mm and 20mm, these cubes cater to a variety of needs, from classroom demonstrations to industrial research. Please note that tin is a toxic material and should be handled with care, avoiding ingestion or inhalation.
Product Specifications
| Material | Tin |
| Density | 7.31 g/cm³ (Constant) |
| Size Options | 10mm or 20mm |
| Weight | Varies by size |
Applications and Benefits:
- Density comparison experiments
- Material studies
- Educational demonstrations
- Industrial research
Key Features and Benefits
- High-density tin construction
- -engineered for accuracy
- Available in 10mm and 20mm sizes
- Suitable for educational and industrial use
- for density comparison and material studies
Caution:
Tin is a toxic material. Handle with care and avoid ingestion or inhalation.
Density Cubes, Metals Zinc
These zinc cubes are for comparing densities and conducting other physical property experiments in the classroom or laboratory. Their precise measurements ensure accurate and consistent results. Each cube is packaged individual20x20 mm, weight 0.115 lb
Product Specifications
| Material: | Zinc |
| Sizes: | 10 mm or 20 mm |
| Packaging: | unit |
| Weight: | 0.115 lb |
| SKU: | 3510A-ZINC |
Applications and Benefits:
- Science education
- Laboratory experiments
- Classroom experiments
- Physical property experiments
- Density comparison
Key Features and Benefits
- Available in 10 mm or 20 mm sizes
- Precise measurements for accurate and consistent results
- zinc material
- Individual reusable plastic box packaging
Caution:
Handle with care when conducting physical property experiments with these zinc cubes. Research is required to find the fit for your needs.
Density Cubes Set 10mm
The Density Cubes Set is an essential tool for understanding metal density and physical properties, featuring twelve meticulously crafted cubes of Iron, Aluminum, Zinc, Lead, Brass, and Copper. Each cube measures 10mm, perfect for comparative studies in science and metallurgy.
Key Features
- Two sets of six different metal cubes
- Precise 10mm cube dimensions
- Included metals: Iron, Aluminum, Zinc, Lead, Brass, Copper
- Ideal for educational and comparative purposes
- Durable and high-quality material composition
Product Specifications
| Materials Included: | Iron, Aluminum, Zinc, Lead, Brass, Copper |
| Dimensions: | 10mm metal cubes |
Similar Products
- Alloy Composition Sampler
- Physics Density Kit
- Educational Metallurgy Set
- Solid Metal Blocks Collection
- Miniature Metals Reference Kit
Note: These are similar products, and each product is different, so research is required to find the best fit for your needs.
Caution: Handle with care due to sharp edges. Not suitable for children without supervision.
Perfect for Science Enthusiasts, Collectors, Students in Metal Studies
Density Cubes, Set Of 5 Non-Metal Cubes
This set of 5 non-metal cubes is an essential tool for exploring and comparing the density and physical properties of different materials. Each cube, made from unique materials like rubber, acrylic, plastic, softwood, and hardwood, measures 20mm. Ideal for educational purposes in physical science and material studies.
Key Features
- Set of 5 different material cubes
- Uniform 20mm size for easy comparison
- Includes rubber, acrylic, plastic, softwood, and hardwood
- Ideal for density and physical properties analysis
- Perfect educational tool for material science
Product Specifications
| Material | Rubber, Acrylic, Plastic, Softwood, Hardwood |
| Size | Each cube 20mm |
| Quantity | 5 cubes |
| Application | Educational, Material Science |
Similar Products
- Transparent acrylic 20mm cube set
- Educational rubber cube collection, 20mm
- Mixed hardwood cube set, 20mm size
- Plastic cube assortment for teaching, 20mm
- Softwood sample cube kit, 20mm
Note: These are similar products, and each product is different, so research is required to find the best fit for your needs.
Perfect for Science educators and teachers, Students in physical or materials science, Homeschooling parents for science lessons, Material science hobbyists, Science museum educational departments
AMM360 Analog Multitester
AMM360 is a desktop analog multitester for measuring DC Volt, AC Volt, DC Current and Resistance. It can also be used as a very sensitive galvanometer and can show as low as 0.01 DC voltage. Additionally, it can be used to test transistors and diodes, making it a versatile tool for any electronics enthusiast. Use it as a voltmeter, ohmmeter, or ammeter to accurately measure a variety of electrical values.
Product Specifications:
| Measurement Types | DC Volt, AC Volt, DC Current, Resistance |
| Sensitivity | Shows as low as 0.01 DC voltage |
| Functions | Can be used as a very sensitive galvanometer, voltmeter, ohmmeter, or ammeter |
| Additional Information | Batteries not included. Please dispose of any battery you may find with your meter. They are non-working. |
Similar Products
- Desktop Digital Multimeter
- Handheld Analog Multimeter
- Benchtop Digital Multimeter
- Clamp Meter
- Insulation Tester
Note: These are similar products, and each product is different, so research is required to find the best fit for your needs.
CAUTION: Batteries not included. Please dispose of any battery you may find with your meter. They are non-working.
Perfect for:
- Electricians and technicians
- DIY enthusiasts and hobbyists
- Engineering students and professionals
- Science teachers and educators
- Anyone who needs to measure electrical properties accurately